您还计划买落伍的单色点阵屏？还是用双基色的吧（实际可显示三种基本颜色）！
不过提示一下，若您要亲手焊接那么光16*32就需要纵横跨接众多线、需要很多时间和一定毅力，管脚要了解清楚哦、还只能显示2个字，不过感到欣慰的是下面是高亮双色的，呵呵...

（自己呆在家里看就行了，挂到外面展示只能出洋相... 以下是一个简单的程序演示此图片的）

       用8*8制作点阵是一件很兴奋而辛苦的事，3.75mm以上点阵还须加中功率三极管或场效应管（推荐）驱动，16*32动态显示电流实测300多～600MA之间，全显近1A（电脑USB线电源掉到4.4～4.6V，最好采用外电源求稳定，避免电脑负荷吃不消）。2个74138输出采用场效应管驱动，8个595列。

驱动电路（仅供参考）：

微控实验网已推出双基色高亮点阵模块、性价比很高>>  http://www.mcusy.cn/Product_Show.asp?id=28

参考程序：
//*********************************************************************
//程序说明：16*32双基色8*8点阵屏演示程序01
// E-mail  ： mcusy_cn@126.com   /Sidney
//电路说明：采用STC89C52单片机，24M晶体；16*32双基色点阵屏需要用154或2个138输出16行，8个595列。
//效果说明：显示8个汉字，每2个轮换显示：“欢迎使用双色点阵”，红、绿、橙色三色轮流变化。
//********************************************************************
#include<reg52.h>
#include<intrins.h>
#define uchar unsigned char
#define uint unsigned int
//---------------------------------------------------------------------------------
sbit SI=P3^0;  
sbit SCK=P3^1;  
sbit STR=P3^3;  
sbit STG=P3^2;  
sbit EN=P1^4;  
uchar j,i,g;
//---------------------------------------------------------------------------------
uchar code table0[][32]={
/*--   文字:   欢   --*/
/*--   宋体12;   此字体下对应的点阵为：宽x高=16x16     --*/
0x00,0x80,0x00,0x80,0xFC,0x80,0x05,0xFE,0x85,0x04,0x4A,0x48,0x28,0x40,0x10,0x40,
0x18,0x40,0x18,0x60,0x24,0xA0,0x24,0x90,0x41,0x18,0x86,0x0E,0x38,0x04,0x00,0x00,
/*--   文字:   迎   --*/
/*--   宋体12;   此字体下对应的点阵为：宽x高=16x16     --*/
0x40,0x00,0x21,0x80,0x36,0x7C,0x24,0x44,0x04,0x44,0x04,0x44,0xE4,0x44,0x24,0x44,
0x25,0x44,0x26,0x54,0x24,0x48,0x20,0x40,0x20,0x40,0x50,0x00,0x8F,0xFE,0x00,0x00,
                                               };
uchar code table1[][32]={
/*--   文字:   使   --*/
/*--   宋体12;   此字体下对应的点阵为：宽x高=16x16     --*/
0x08,0x40,0x0C,0x40,0x1B,0xFE,0x10,0x40,0x37,0xFC,0x64,0x44,0xA4,0x44,0x27,0xFC,
0x24,0x44,0x22,0x40,0x21,0x80,0x20,0x80,0x21,0x70,0x22,0x1E,0x2C,0x04,0x00,0x00,

/*--   文字:   用   --*/
/*--   宋体12;   此字体下对应的点阵为：宽x高=16x16     --*/
0x00,0x00,0x1F,0xFC,0x10,0x84,0x10,0x84,0x10,0x84,0x1F,0xFC,0x10,0x84,0x10,0x84,
0x10,0x84,0x1F,0xFC,0x10,0x84,0x10,0x84,0x20,0x84,0x20,0x94,0x40,0x8C,0x00,0x00,
                                               };
uchar code table2[][32]={
/*--   文字:   双   --*/
/*--   楷体_GB231212;   此字体下对应的点阵为：宽x高=16x16     --*/
0x00,0x00,0x00,0x00,0x00,0x30,0x0C,0xD0,0x74,0x10,0x25,0x10,0x14,0xA0,0x08,0x40,
0x08,0x40,0x14,0xA0,0x25,0x18,0xC2,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,

/*--   文字:   色   --*/
/*--   楷体_GB231212;   此字体下对应的点阵为：宽x高=16x16     --*/
0x02,0x00,0x02,0x00,0x07,0xC0,0x08,0x80,0x11,0x00,0x03,0xE0,0x1E,0x20,0x12,0x40,
0x13,0xC0,0x1C,0x00,0x10,0x04,0x10,0x04,0x10,0x04,0x0F,0xF8,0x00,0x00,0x00,0x00,
                                               };
uchar code table3[][32]={
/*--   文字:   点   --*/
/*--   楷体_GB231212;   此字体下对应的点阵为：宽x高=16x16     --*/
0x00,0x00,0x02,0x00,0x02,0x60,0x03,0x80,0x02,0x00,0x02,0x00,0x03,0xE0,0x0C,0x20,
0x08,0x20,0x0F,0xC0,0x00,0x00,0x48,0x90,0x44,0x4C,0x80,0x04,0x00,0x00,0x00,0x00,

/*--   文字:   阵   --*/
/*--   楷体_GB231212;   此字体下对应的点阵为：宽x高=16x16     --*/
0x00,0x00,0x18,0x40,0x68,0x70,0x4B,0x80,0x50,0x80,0x49,0x40,0x6A,0x78,0x5B,0xC0,
0x40,0x40,0x40,0x7E,0x4F,0xC0,0x40,0x40,0x40,0x40,0x00,0x40,0x00,0x40,0x00,0x00,
                                                 };
uchar code table4[][32]={
/*--   文字:   点   --*/
/*--   楷体_GB231212;   此字体下对应的点阵为：宽x高=16x16     --*/
0x00,0x00,0x02,0x00,0x02,0x60,0x03,0x80,0x02,0x00,0x02,0x00,0x03,0xE0,0x0C,0x20,
0x08,0x20,0x0F,0xC0,0x00,0x00,0x48,0x90,0x44,0x4C,0x80,0x04,0x00,0x00,0x00,0x00,

/*--   文字:   阵   --*/
/*--   楷体_GB231212;   此字体下对应的点阵为：宽x高=16x16     --*/
0x00,0x00,0x18,0x40,0x68,0x70,0x4B,0x80,0x50,0x80,0x49,0x40,0x6A,0x78,0x5B,0xC0,
0x40,0x40,0x40,0x7E,0x4F,0xC0,0x40,0x40,0x40,0x40,0x00,0x40,0x00,0x40,0x00,0x00,
                                                 };
//------------------------------------------------------------------------------
void delay(uint g)
{
   uint m,s;
   for(m=0;m<g;m++)
         for(s=0;s<30;s++);
}
//------------------------------------------------------------------------------
void send_dat(uchar temp)//发送
{
  uchar j;
  for(j=0;j<8;j++)
       {
         SI=~temp&0x01; //~temp显示不反白,把0x01改成0X80字体将反白
         SCK=0;SCK=1;
         temp=temp>>1;
       }
}
void dis_red(void)//------锁存函数
{    
   EN=1;           //关显示
   STR=1;STG=0; //开红色、关绿色
   P1=i;  
   STR=0;STG=0;  
   EN=0;           //开显示
}
void dis_green(void)
{
   EN=1;
   STR=0;STG=1; //开绿色、关红色
   P1=i;
   STR=0;STG=0;
   EN=0;
}
void dis_orange(void)
{
   EN=1;
   STR=1;STG=1;   //开红＋绿色＝橙色
   P1=i;
   STR=0;STG=0;
   EN=0;
}
//------------------------------------------------------------------------------
void display(uchar *data1,uchar *data2)
{
     uchar num;
     for(num=0;num<30;num++)
       {
         for(i=0;i<16;i++)
                 {
  send_dat(data2[2*i+1]);send_dat(data2[2*i]);//字体的位置，可调整
  send_dat(data1[2*i+1]);send_dat(data1[2*i]);
  dis_red();
  delay(5);
                 }
           }
     for(num=0;num<30;num++)
       {
         for(i=0;i<16;i++)
                 {
  send_dat(data2[2*i+1]);send_dat(data2[2*i]);
  send_dat(data1[2*i+1]);send_dat(data1[2*i]);
  dis_green();
  delay(5);
                 }
           }
       for(num=0;num<30;num++)
       {
         for(i=0;i<16;i++)
                 {
  send_dat(data2[2*i+1]);send_dat(data2[2*i]);
  send_dat(data1[2*i+1]);send_dat(data1[2*i]);
                   dis_orange();
  delay(5);
  EN=0;
                 }
           }
}
//===========================主函数==========================//
void main()
{
  while(1)//-----以下是调用显示函数
     {
         display(table0[0],table0[1]);delay(5000);
         display(table1[0],table1[1]);delay(5000);
         display(table2[0],table2[1]);delay(5000);
         display(table3[0],table3[1]);delay(20000);
         }
}

  

  

• 评论内容...
• 匿名发表
• [添加到收藏夹]
• 发表评论：(匿名发表无需登录，已登录用户可直接发表。) 登录状态：未登录